Results 1 to 5 of 5
November 5th, 2010, 04:21 AM #1govin Guest
process of H2 and N2 Mixing plant.
I am going to installed redundant system in our very critical process of H2 and N2 Mixing plant.We got a offer from a siemens supplier –
I want to know that this system is ok can i got both redundancy (HWR & SWR) in this CPU. if i got only software redundancy what will be the loss in this.
as per my opinion i need both SWR as well as HWR .please guide me if you know about this….
S.No. DESCRIPTION Make QTY
1 CPU 315-2DP Siemens 2
2 MMC 128KB Siemens 2
3 RAIL, 160MM Siemens 2
4 P.S. 5A Siemens 4
5 PS 10A Siemens 1
6 Redundancy Bundle Siemens 2
7 Active Rail Siemens 2
8 Active Bus Modules Siemens 6
9 16 DI Siemens 2
10 8DO Siemens 2
11 8 AI Siemens 6
12 8 AO Siemens 2
13 40 PIN FRT.CONN. Siemens 8
14 20 PIN FRT.CONN. Siemens 4
15 Profibus conn without PGI Siemens 4
16 Profibus conn with PGI Siemens 2
17 Profibus Cable Siemens 400
18 WinCC 128 Run Time Siemens 2
19 CP5611 Siemens 2
20 Step 7 Basic Package V5.4 Siemens 1
21 Control transformer Reputed 1
22 MCB DP 4 A for traffo i/p Siemens 1
23 MCB DP 6 A for traffo o/p Siemens 1
24 Fan with filter 6'' 220V Reputed 2
25 Illumination light 20W 220V AC Reputed 1
26 Door switch Reputed 1
27 MCB SP 2A for cooling fan & light Siemens 1
28 Cabinet Rittal Make 1
29 PC with cabinet/consol Reputed 2
November 5th, 2010, 04:34 AM #2WWF_Champ Guest
You will need a few WinCC Flexible licenses to operate a Runtime application. Start with the following manual that will explain the different licence levels and their application:
November 5th, 2010, 04:44 AM #3WeeLi Guest
I am not sure how the Software Redundancy will be used with a WinCC Flexible Runtime licence: whether you will need to have two distinct stations, each with their licewnses and CP 5611... I hope someone with more information on the subject can add something here..
November 5th, 2010, 04:56 AM #4TomLee Guest
You can use only one Red. bundle if you like.
The IM153-2 HF supports up to 12 modules.
November 5th, 2010, 05:04 AM #5ZUDD Guest
I cannot say about the hardware section, this you would need to check out by yourself, possibly using the Simatic Hardware Configurator from the Industry Mall:
By plantautomation in forum Automation Forum NewsReplies: 0Last Post: April 24th, 2012, 01:54 AM
By SJAY in forum Automation Applications & SoftwareReplies: 5Last Post: October 24th, 2010, 04:25 AM
By BELLA5 in forum Programming LanguagesReplies: 6Last Post: October 21st, 2010, 07:52 AM
By Bill O. in forum Automation Applications & SoftwareReplies: 2Last Post: September 12th, 2006, 04:01 PM